The Billionth Repository On GitHub Is Really Shitty

June 12, 2025 by Jenny List 21 Comments

What’s the GitHub repository you have created that you think is of most note? Which one do you think of as your magnum opus, the one that you will be remembered by? Was it the CAD files and schematics of a device for ending world hunger, or perhaps it was software designed to end poverty? Spare a thought for [AasishPokhrel] then, for his latest repository is one that he’ll be remembered by for all the wrong reasons. The poor guy created a repository with a scatalogical name, no doubt to store random things, but had the misfortune to inadvertently create the billionth repository on GitHub.

At the time of writing, the 💩 repository sadly contains no commits. But he seems to have won an unexpectedly valuable piece of Internet real estate judging by the attention it’s received, and if we were him we’d be scrambling to fill it with whatever wisdom we wanted the world to see. A peek at his other repos suggests he’s busy learning JavaScript, and we wish him luck in that endeavor.

We think everyone will at some time or another have let loose some code into the wild perhaps with a comment they later regret, or a silly name that later comes back to haunt them. We know we have. So enjoy a giggle at his expense, but don’t give him a hard time. After all, this much entertainment should be rewarded.

This Relay Computer Has Magnetic Tape Storage

June 11, 2025 by Jenny List 8 Comments

Magnetic tape storage is something many of us will associate with 8-bit microcomputers or 1960s mainframe computers, but it still has a place in the modern data center for long-term backups. It’s likely not to be the first storage tech that would spring to mind when considering a relay computer, but that’s just what [DiPDoT] has done by giving his machine tape storage.

We like this hack, in particular because it’s synchronous. Where the cassette storage of old just had the data stream, this one uses both channels of a stereo cassette deck, one for clock and the other data. It’s encoded as a sequence of tones, which are amplified at playback (by a tube amp, of course) to drive a rectifier which fires the relay.

On the record side the tones are made by an Arduino, something which we fully understand but at the same time can’t help wondering whether something electromechanical could be used instead. Either way, it works well enough to fill a relay shift register with each byte, which can then be transferred to the memory. It’s detailed in a series of videos, the first of which we’ve paced below the break.

If you want more cassette tape goodness, while this may be the slowest, someone else is making a much faster cassette interface. Continue reading “This Relay Computer Has Magnetic Tape Storage” →

Let’s Buy Commodore! Well, Somebody Is.

June 7, 2025 by Jenny List 52 Comments

When a man wearing an Atari T-shirt tells you he’s buying Commodore it sounds like the plot for an improbable 1980s movie in which Nolan Bushnell and Jack Tramiel do battle before a neon synthwave sunset to a pulsating chiptune soundtrack. But here on the screen there’s that guy doing just that, It’s [Retro Recipes], and in the video below he’s assembling a licensing deal for the Commodore brand portfolio from the distant descendant of the Commodore of old.

It’s a fascinating story and we commend him for tracing a path through the mess that unfolded for Commodore in the 1990s. We tried the same research path with a friend a few years ago and ended up with an anonymous Dutch paper company that wouldn’t answer our calls, so we’re impressed. In conjunction with several other players in the Commodore retrocomputing world he’s trying to assemble a favourable percentage deal for manufacturers of new parts, computers, and other goodies, and we’re pleased to see that it’s for the smaller player as much as for the industry giant.

When looking at a story like this though, it’s important not to let your view become clouded by those rose tinted glasses. While it’s great that we’re likely to see a bunch of new Commodore-branded Commodore 64s and parts, there are many pitfalls in taking it beyond that. We’ve seen the Commodore logo on too many regrettable licensed products in the past, and we fear it might be too tempting for it to end up on yet another disappointing all-in-one video game or just another budget PC. If something new comes out under the Commodore brand we’d like it to be really special, exploiting new ground in the way the Amiga did back in the day. We can hope, because the alternative has dragged other famous brands through the mud in recent years.

If you want an insight into the roots of the original Commodore’s demise, have a read of our Hackaday colleague [Bil Herd]’s autobiography.

Continue reading “Let’s Buy Commodore! Well, Somebody Is.” →

Printed Focus Control For Pro Style Cinematography

June 7, 2025 by Jenny List 14 Comments

When you watch a movie and see those perfect focus switches or zooms, the chances are you’re not seeing the result of the cameraman or focus operator manually moving the lens controls. Instead, they will have been planned and programmed in advance and executed by a motor. If you take a close look at many lenses you’ll see a ring that’s more than just extra knurling, it’s a gear wheel for this purpose. Want to experiment with this technique without buying professional grade accessories? [l0u0k0e] has you covered with a 3D printable focus zoom motor accessory.

The motor behind it all is a geared stepper motor, and there are a set of printed parts to complete the model. It’s recommended to use PETG, and nylon for the gears, but it would work in PLA with a shorter life. It’s designed to work with the standard 15 mm tube you’ll find on many camera rigs, and while you can write your own Arduino sketches to control it if you wish, we’re given instructions for hooking it up to existing focus drivers. The model is on Printables, should you wish to try.

This is by no means the first focus puller we’ve seen, in fact you can even use LEGO.

A Network Status Panel The Way It Should Be

June 6, 2025 by Jenny List 16 Comments

Sometimes a project forms itself around a component rather than an idea, and thus it was that [Maximilien] found himself building a data rate monitor for the connection between two data centers. Some MD0657C2-R LED dot matrix displays for not a lot needed a project.

The displays are mounted in groups of four on small PCBs, driven by a MAX6952, which are then controlled by a Pi Pico. There are several display panels in the project, each of which is a pained and laser-etched acrylic sheet with a pair of the LED boards mounted behind it. These in turn go on the front of a wooden enclosure, with a set of LED ring lights behind to illuminate the etched parts of the panels. Each display panel has its own Pico, daisy chained together and driven by a Pico W that supplies network connectivity.

As you might expect, this isn’t the first status panel we’ve brought you over the years.

In Film, What’s Old May Still Be New Again

June 6, 2025 by Jenny List 15 Comments

We recently published an affectionate look at a Polaroid Land camera, whose peel-apart instant film is long out of production except for a very few single exposure packs form a boutique manufacturer. All that was left was a discussion of modifying it for conventional roll film, or perhaps hacking a modern back-to-front Polaroid sheet into it.

Never say never though, because along come the Chinese company Light Lens Lab with a short announcement at the end of a post talking about grain structures and anti-halation layer materials for their black and white film.

Lastly, with our future development plan, we are currently developing and researching instant peel-apart film, with plans on producing and making available black and white peel-apart film by 2025 in various format. We aim to have an update on our packaging and test shot for the next development/research progress installment. We are also researching, developing and producing colour reversal films that consist of a dye-incorporating development process, commonly known as K-14, for 135 and 120 formats in 2026.

So there you go, no sooner has Hackaday declared a format unavailable, than it shows every sign of reappearing. At this point we’d like to take the opportunity to report that McDonalds Szechuan Chicken McNugget sauce will never ever be available again. Continue reading “In Film, What’s Old May Still Be New Again” →

A Steady Vacuum For The Fastest Cassette Tape Drive Ever

June 5, 2025 by Jenny List 39 Comments

If you think of a 1960s mainframe computer, it’s likely that your mental image includes alongside the cabinets with the blinkenlights, a row of reel-to-reel tape drives. These refrigerator-sized units had a superficial resemblance to an audio tape deck, but with the tape hanging down in a loop either side of the head assembly. This loop was held by a vacuum to allow faster random access speeds at the head, and this fascinates [Thorbjörn Jemander]. He’s trying to create a cassette tape drive that can load 64 kilobytes in ten seconds, so he’s starting by replicating the vacuum columns of old.

The video below is the first of a series on this project, and aside from explaining the tape drive’s operation, it’s really an in-depth exploration of centrifugal fan design. He discovers that it’s speed rather than special impeller design that matters, and in particular a closed impeller delivers the required vacuum. We like his home-made manometer in particular.

What he comes up with is a 3D printed contraption with a big 12 volt motor on the back, and a slot for a cassette on the front. It achieves the right pressure, and pulls the tape neatly down into a pair of loops. We’d be curious to know whether a faster motor such as you might find in a drone would deliver more for less drama, but we can see the genesis of a fascinating project here. Definitely a series to watch.

Meanwhile, if your interest extends to those early machine rooms, have a wallow in the past.

Continue reading “A Steady Vacuum For The Fastest Cassette Tape Drive Ever” →